Jumpguard Pro DIY Aquarium Net 75cm x 75cm

£41.99

D-D Jumpguard covers are a very lightweight, sleek, low visual impact and easy to construct screen cover suitable for most aquarium types, specifically designed to prevent fish loss due to jumping whilst maintaining high light penetration.

The new Jumpguard Pro now includes cut-out and brace bar parts as standard and an aesthetic black mesh.

Available in 3 sizes, from 75-180cm long.

In stock

- +

Description

Jumpguard Pro DIY Aquarium Cover

There is nothing worse than coming down in the morning to finding your favourite fish lying dead and crispy on the carpet.

Many fish, especially wrasse, tend to jump from the tank when frightened or chased by another fish and so a solution to preventing the loss of such fish should be high on every fish keeper’s priority list.

D-D Jumpguard covers are a very lightweight, sleek, low visual impact and easy to construct screen cover suitable for most aquarium types, specifically designed to prevent fish loss due to jumping whilst maintaining high light penetration.

The new Jumpguard Pro now includes cutout and brace bar parts as standard and an aesthetic black mesh.

Available in the following versions and are designed to be cut to size:

  • MA710 – TC7575PRO – 75cm x 75cm nominal size. (29.5 inches x 29.5 inches)
  • MA711 – TC12075PRO – 120cm x 75cm nominal size. (47.25 inches x 29.5 inches)
  • MA712 – TC18090PRO – 180cm x 90cm nominal size. (70.8 inches x 35.4 inches)

Notes:

  • The maximum size frame that can be made from each kit will be 3.6cm (1.4 inches) longer than stated in each direction.
  • The tank should be measured from inside face of glass to inside face of glass and not the outer dimensions of the tank, which will vary due to glass thickness.

The Jumpguard Pro Aquarium Cover is a kit of parts which allows the aquarist to create a custom frame for their specific aquarium. The rigid corners and extruded aluminium section create a very solid frame which sits neatly inside glass of the aquarium glass, resting on the top lip.

Kit Contents:

MA710 – (TC7575PRO) Jumpguard Pro DIY Aquarium Net 75cm x 75cm

  • Black mesh – 90cm x 90cm (36″ x 36″).
  • 5 x 75cm lengths of section in black extrusion profile.
  • 1 x red spline roller tool.
  • 6 x black standard corners.
  • Black spline, total length 3.5m.
  • 2 x Black finger pull.
  • 2 x Reverse corner.
  • 1 x 75cm brace bar.
  • 4 x brace clips

Features of the Jumpguard Pro Aquarium Cover

NEW PROFILE DESIGN

  • The special extruded aluminium profile is now shaped with a lip which sits directly onto the edge of the glass, removing the requirement for any additional clips or brackets. The section is extruded then powder coated in a tough, low sheen, black finish for greater scratch resistance and greater aesthetics.

SPECIAL CORNERS INTEGRATE WITH SILICONE JOINTS

  • The lower section of the corners is specifically designed so that it does not interfere with the silicone bead in the corners of your tank which gives a tight fit to the glass with no gaps. It also makes it easier and neater to cut off the corner if you want to bring wires out at the back of the tank for pumps and heaters.

NEW BLACK MESH WITH MAXIMUM LIGHT PENETRATION

  • For those concerned with loss of light penetration into your reef tanks, we tested light levels with an Apogee MQ-200 meter and got the following results:
  • PAR without cover around 390 – 400 • PAR with cover around 380 – 390 • Approximately a 2.5% reduction in light with no shadowing at all.

The new Jumpguard PRO is supplied with the new black as standard in all size versions.

On the tank it is much harder to see than the clear mesh as you do not get the same light bounce back.